TURBO TROUBLESHOOTING

All too frequently, serviceable turbochargers are removed from engines before the cause of the problem has been determined. Always inspect and assess turbocharger condition before removal from the engine.

Should removal of the turbo become necessary, try to determine if the connections were tight and without leaks while you are removing the hoses, clamps or connections.  Once disassembly has been completed, it may be difficult or impossible to substantiate the conditions that caused the problem.

Problems experienced in the field can most often be corrected by system troubleshooting.  Immediate or early failure of a replacement turbocharger may be related to:

• The incomplete correction of the problem that caused the need for the replacement.
• Problems introduced during the replacement.
• A defective turbocharger.

A turbocharger that has operated successfully is very unlikely to be found defective at a later date.  Speed and temperature normally seen in turbocharger operation usually identify defects very quickly.  Installation or engine system problems can also show up immediately upon replacement.  Don't be too quick to blame the turbo for operational problems if the turbocharger spins freely and has not rubbed the housing.

It should be emphasized that a turbocharger does not basically change the operating characteristics of an engine.  A turbocharger is not a power source within itself.  The turbo's only function is to supply a greater volume of compressed air to the engine so that more fuel can be burned to produce more power.  It can function only as dictated by the flow, pressure and temperature in the engine exhaust gas.

Turbochargers are an integral component of a complete operating system.  Only by convenience is a turbo external or 'bolt-on" in installation.  It is no less dedicated than an engine's camshaft or pistons.  Understanding how a turbocharger is part of a complete engine management system is essential in successfully diagnosing and repairing problems.  Likewise, a better understanding of some of a turbocharger's features can be helpful when determining that a turbo is damaged or defective, and installing it correctly the first time, every time.

Verify that the turbocharger is the correct configuration for the application.  Assembly and component part numbers may both need attention.  This is particularly important because the "matching" process requires subtle component differences.  Part number checks are necessary because some of the possible discrepancies will not be apparent to the untrained eye.

A turbocharger cannot correct or overcome such things as malfunctions or deficiencies in the engine fuel system, timing, plugged air cleaners, faulty liners, etc.  Therefore, if a turbocharged engine system has malfunctioned and the turbocharger has been examined and determined to be operational, proceed with troubleshooting, as though the engine were non-turbocharged.  Simply replacing a good turbocharger with another will not correct basic engine deficiencies.

Common Symptoms

Turbochargers and engines have common problem symptoms.

• Engine Lacks Power
• Engine Exhaust Smoke
• Oil Consumption
• Noisy Operation

Any of these symptoms could be the result of an internal engine problem and might not involve the turbocharger at all.  The following on-engine troubleshooting guide is designed to quickly determine turbocharger condition and prevent unnecessary removal.

On Engine Troubleshooting

Many of the problem causing conditions will appear in direct or inverse proportion to the power output.  For example, there may be a problem at idle that is unnoticeable at full power or visa versa.  The following procedures are an overall evaluation involving varying operational conditions.  On-engine troubleshooting will also help to expose any external or engine related causes of turbocharger failure that must be corrected to prevent the failure of a replacement unit.

The most efficient way to troubleshoot a performance complaint is to proceed through all of the steps in the order presented before making a final determination of the service required.  It is extremely important that all in-service problem areas are examined before any single one is corrected.

In some instances, corrective service may lead you to turbocharger Damage Analysis and, depending on the results of these inspections and/or the turbocharger model, you may also have to measure the bearing clearances or test the wastegate device. Those inspections, as well as a detailed analysis of problems that may be exposed here, are also covered in turbocharger Damage Analysis.

On-engine troubleshooting consists of several basic steps that should be taken before the turbocharger is removed from the engine.  Any external or engine-related faults found must be corrected before a replacement turbocharger is installed.

Refer to the engine manufacturer's service instructions for inspection requirements and replacement specifications.

CAUTION: Do not run the engine during these procedures. If the engine has been running, make sure it is cool before beginning.

Warning:  Operating the turbocharger without the inlet duct and air filter connected can result in personal injury. Equipment damage may result from foreign objects entering the turbocharger.

The basic steps to troubleshooting are as follows:

VISUAL AND MECHANICAL CHECKS

Inspect the turbocharger exterior and installation.  Listen for unusual mechanical noises.  Visually check and test for leaks, blockage, high heat, restrictions or conditions that have allowed wheels to contact the housings.  Leaks that are seemingly small and insignificant at idle or low power can greatly affect air/fuel ratios and pressures within the housing and full power.  At full power, those leaks become problematic.

• Listen for unusual mechanical noise and watch for vibration.
• Listen for a high pitched noise.  It can indicate air or gas leaks.
• Listen for noise level cycling.  It can indicate a restriction in the air cleaner or ducting.
• Inspect for missing or loose nuts, bolts, clamps and washers.
• Inspect for loose or damaged intake and exhaust manifolds and their ducting and clamps.
• Inspect for damaged or restricted oil supply and drain lines.
• Inspect for cracked or deteriorating turbocharger housings.
• Inspect for external oil or coolant leakage; external deposits (indicates air, oil, exhaust or coolant leakage).
• Inspect for obvious heat discoloration.
• Inspect for obviously restricted air filter.
• Check the wastegate for free movement and damage.  Be sure that hoses are in good condition and that the connections are tight.  Check the calibration and control system according to the original equipment specifications.
• Verify that the turbocharger is the correct configuration for the application.

Remember, correcting these problems does not in it self remove any residues that were the indicators of the problem.  The remaining residues often cause inaccurate turbocharger evaluation.  Incorrect turbocharger evaluation may result after the situation has been corrected and the residues remain.  For example, an air filter replaced just previous to your inspection would lead you to conclude that air blockage is not the problem even though the residue indicates blockage.

Correct any installation problems after completing the rest of this procedure.  If turbocharger parts are damaged, then the unit should be replaced at this time and corrective actions taken to prevent reoccurrence.

Refer to the engine manufacturer's service instructions for inspection requirements and replacement specifications.

CAUTION: Do not run the engine during these procedures. If the engine has been running make sure it is cool before beginning.

Warning:  Operating the turbocharger without the inlet duct and air filter connected can result In personal injury. Equipment damage may result from foreign objects entering the turbocharger.

TURBINE WHEEL AND TURBINE HOUSING CHECKS

Remove the ducting from the turbine outlet. Using an inspection light:

Inspect the turbine for evidence of foreign object damage.  This is usually not easily visible from the turbine outlet unless the damage is severe.  Determine the source of the object and check for possible engine damage.  Figure 20 highlights where turbine wheel rub frequently occurs.

Turn the rotating assembly by hand and feel for dragging or binding; also check by pushing the assembly sideways while turning. The wheel should turn freely and without any rubbing or scraping noises.  If there are obvious signs of wheel rub or that the turbine housing has been operated at excessive temperatures, then the turbocharger is damaged and must be replaced.  If you are still not sure whether the wheel is rubbing, inspect the bearing clearances after completing this section.

Look for evidence of oil leakage.  If oil deposits are found, then determine whether the oil is from the engine or from the turbocharger center housing.  Some oil residues may be cleaned; heavy oil residues may require replacement.  If the oil is from the center housing, then remove the oil drain line and look into the turbocharger drain opening and drain line with an inspection light.  Check for an oily, sludge build-up on the shaft between the bearing journals, in the drain cavity, and in the drain line.

Check the following to determine the cause of the problem and effect corrections as necessary:

• Restricted draining or high crankcase pressure can raise the pressure of the center housing drain area above the pressure in the turbine housing forcing oil in that direction.
• PCV flow control valves on spark ignition engines must operate as one way check valves when boost is developed.  This reverses the direction of flow in the ventilation system.  A partially closed PCV allows manifold boost to pressurize the crankcase.
• Damaged oil drain line.
• Improper line routing (more than 35 degrees from vertical or any sharp bends) or routings close to exhaust manifolds.
• Submerged drain line from too high an oil level or equipment operated at extreme angle.

Correct any installation problems after completing the rest of this procedure.  If turbocharger parts are damaged, the unit should be replaced at this time and corrective actions taken to prevent reoccurrence.

Refer to the engine manufacturer’s service instructions for inspection requirements and replacement specifications.

CAUTION: Do not run the engine during these procedures. If the engine has been running make sure it is cool before beginning.

Warning:  Operating the turbocharger without the inlet duct and air filter connected can result in personal injury.  Equipment damage may result from foreign objects entering the turbocharger.

COMPRESSOR WHEEL AND COMPRESSOR HOUSING CHECKS

Remove the ducting from the compressor inlet. Using an inspection light:

Inspect the compressor for evidence of foreign object damage.  If the wheel is damaged, the foreign object probably entered through the intake system.  Remember that the origin of foreign object damage should be identified.  Foreign objects usually come from human error or deteriorated intake systems.  Determine the source of the object, clean the system, and check for possible engine damage.

Turn the rotating assembly by hand and feel for dragging or binding; also check by pushing the assembly sideways while turning. Look for any evidence of wheel rub.  Wheel rub can be caused by loose, distorted, or binding housings as well as damaged bearings. If there is still any doubt, inspect the bearing clearances.

Look for evidence of oil leakage.  The compressor side is most sensitive to a restricted air inlet.  Oil in the compressor outlet does not prove turbocharger seal leakage.  Oil from crankcase ventilation or other oil sources can be confused with compressor-side oil leaks.  The turbocharger compressor can take oil vapor and expel it as liquid oil.  General engine condition greatly affects engine crankcase ventilation system operation.  Follow manufacturer's recommendations.  Other factors that can cause oil leakage into the compressor are detailed in the Troubleshooting charts.  Compressor oil leaks can result in oil accumulations in the charge-air cooler.  When all problems have been corrected this oil can be transferred into the engine. I f oil accumulation occurs, it will require draining and cleaning of the charge-air cooler.

Correct any installation problems after completing the rest of this procedure. If turbocharger parts are damaged, the unit should be replaced at this time and

Refer to the engine manufacturer's service instructions for inspection requirements and replacement specifications.

CAUTION: Do not run the engine during these procedures. If the engine has been running, make sure it is cool before beginning.

Warning: Operating the turbocharger without the inlet duct and air filter connected can result in personal injury.  Equipment damage may result from foreign objects entering the turbocharger.

ROTATING ASSEMBLY CHECK

Check for signs of a sludged or coked center housing. A sludged or coked center housing will not likely be evident by inspecting the end housings. Evidence of this condition will be found in advanced cases by looking for oil deposits in the oil inlet. Also check the oil drain area.

Turn the rotating assembly by hand and feel for dragging or binding; also check by pushing the assembly sideways while turning. Look for any evidence of wheel rub. Wheel rub can be caused by loose, distorted, or binding housings as well as damaged bearings. If there is still any doubt, inspect the bearing clearances.

Look for evidence of leakage; either oil and/or coolant.

• Loose or improper connections.
• Improper gaskets or gasket material.
• Casting porosity.
• Improperly drilled holes.

CHECK RADIAL AND AXIAL BEARING CLEARANCES

If none of the previous steps have revealed any turbocharger faults, or if the evidence is not conclusive, this procedure will show if the unit is worn or damaged internally to the point of needing replacement.

Radial Journal Bearing Clearance Note: Due to the unique location of the internal opening in the center housing casting on models T45 and T51, access to the shaft wheel at this point is difficult.

Check the radial clearance of the journal bearings as follows:

For all models, except T45 and T51, attach the turbocharger gauge set to the unit so that the dial indicator plunger extends through the oil drain port and contacts the shaft of the turbine wheel assembly.

For models T45 and T51 only, place the special curved end of the gauge arm in contact with the wheel shaft through the oil outlet port and the internal opening in the casting.

• The dial indicator shaft is then placed in contact with the exposed portion of the gauge arm at a point equidistant from the gauge arm pivot and a point of contact with the wheel shaft, with the arm kept in contact with the shaft by the spring action of the dial indicator plunger.
• Manually apply pressure equally and simultaneously to the compressor and turbine wheels to move the shaft as far as it will go away from the dial indicator plunger.
• Set the dial indicator to zero.
• Manually apply pressure equally and simultaneously to the compressor and turbine wheels to move the shaft as far as it will go toward the dial indicator plunger.  Note the maximum shaft movement shown on the indicator dial.
• To make sure that the dial indicator reading is the maximum possible, roll the wheels slightly in one direction and then the other while applying pressure.
• Manually apply pressure equally and simultaneously to the compressor and turbine wheels to move the shaft as far as it will go away from the dial indicator plunger.  Make sure the dial indicator pointer returns to zero.
• Repeat steps "b" through "f" several times to make sure that the maximum bearing radial clearance, as indicated by the maximum shaft movement, has been measured.
• Compare the maximum clearance measured to the specification for bearing radial clearance for the model turbocharger being tested, as found in the specifications section of your catalog.  If the measurement is within the specification, the journal bearings are in good condition.  If the measurement is not within the specification, the turbocharger is worn or damaged internally and must be replaced.

Axial (Thrust) Bearing Clearance Check the axial clearance of the thrust bearing as follows:

• Clean the hub end of the turbine wheel assembly.
• Attach a turbocharger gage set to the turbine end of the turbocharger so that the dial indicator plunger rests on the hub end of the turbine wheel assembly.
• Manually apply pressure to the compressor wheel and turbine wheel assembly to move the assembly as far as it will go away from the turbine end of the turbocharger (away from the dial indicator plunger).
• Set the dial indicator to zero.
• Manually apply pressure to the compressor wheel and turbine wheel assembly to move the assembly as far as it will go toward the turbine end of the turbocharger (toward the dial indicator plunger).  Note the maximum shaft movement shown on the indicator dial.
• Repeat steps "c" through "e" several times to make sure that the maximum bearing axial clearance, as indicated by the maximum turbine wheel assembly movement, has been measured.
• Compare the minimum and maximum clearance measured to the specification for bearing axial clearance for the model turbocharger being tested, as found in the specifications section of your catalog.

If the measurement is within the specification, the thrust bearing is in good condition.  If no other faults have been found in previous steps, the turbocharger is likely not at fault in the complaint.  Troubleshoot the engine as instructed in the engine manufacturer's service manual.

If the turbocharger was recently replaced or overhauled, make certain that the proper unit was installed or that the right parts were used in the overhaul.  A turbocharger can appear to be right for the installation, but if the turbine and compressor components are not identical to those recommended by the engine manufacturer, performance and service life can suffer.

If the measurement is out of specification, the turbocharger is worn or damaged internally and must be replaced.

WASTEGATE ASSEMBLY CHECK

Wastegates may be an integral part of the turbine housing or a separate device plumbed into the exhaust system.  Actuators are connected directly to the compressor outlet or work in conjunction with the engine management system.  Engine manufacturers supply specific information on wastegates because of their arrangement within the engine management system.

Actuators spring pre-load may be high enough to make checking for free movement by hand difficult or impossible.  Visually check for obstacles that can prevent movement or closure.  Inverted exhaust pipe connection studs can prevent some wastegates from opening.  Stress relief cracking may be found around the relief port in turbine housings.  Cracks that do not extend beyond the wastegate valve do not present a problem.

CAUTION! When checking an actuator do not over pressurize because the diaphragm may become damaged.  Swing valve actuators should move smoothly and show no decay when subjected to calibration pressures.  Many poppet valve units have a hollow stem that opens in the guide giving a small leak when pressurized.  Poppet valve units also depend to some degree on engine vibration to overcome static friction.  When checking this type unit, light tapping of the housing will usually provide an accurate calibration check.

Original equipment specifications for calibration should be closely followed because they are established to interact with the entire engine management system. The calibration pressure is not necessarily a reflection of expected manifold boost because other pressures act on the valve.  In many cases pressure to the actuator is overridden by the engine control system to vary the amount of boost depending upon conditions.

Many actuators are mounted on a bracket away from high temperatures.  Problems may come from bending of the brackets or rods.  High temperatures from exhaust leaks, corrosion, or other loose or damaged components can also result in wastegate problems.

When all else fails ask somebody that knows.